Bulletin Samara State Agricultural AcademyBulletin Samara State Agricultural Academy1997-32252782-4225Samara State Agrarian University100713Research ArticleOPTIMIZATION OF DESIGN AND PROCESS PARAMETERS OF THE PEG-WHEEL FEEDSyrkinV. A.senior lecturer of the Department of «Electrification and Automation of the Agro-industrial Complex»sirkin_va@mailMashkovS. V.Candidate of Economic Sciences, Head of the Department of «Electrification and Automation of the Agro-industrial Complex»mash_ser@mail.ruIshkinP. A.Candidate of Technical Sciences, Associate Professor of the Department «Electrification and Automation of the Agro-industrial Complex»ishkin_pa@mail.ruVasilievS. I.Candidate of Technical Sciences, Associate Professor of the Department «Electrification and Automation of the Agro-industrial Complex»si_vasilev@mail.ruFSBEI HE Samara State Agrarian University1509202163394614022022Copyright © 2021, Syrkin V.A., Mashkov S.V., Ishkin P.A., Vasiliev S.I.2021The purpose of the research is to improve the quality of the seeding process of a peg-wheel feed. Plant breeding centers raise strict requirements to operational process of seeding quality and works are performed by nursery planters. One of main structural elements of a nursery planter that affects the qualitative and quantitative characteristics of sowing is the seed drill. The most widespread among the seeding devices were peg-wheel with grooves. However, seeding devices of this type have disadvantages, one of which is the creation of a pulsating seed duct that increases the uneven seeding, leading to a decrease in the sowing quality. Peg-wheel feeds have no this disadvantage but possess a higher even seeding quality. A new design of a peg-wheel feed has been proposed, which roller is made up of three pin disks, two laterals and one central. During operation of the roller, the lateral disks rotate ahead of the central one, which contributes to an increase of even seeding. In order to identify the optimal parameters of the seeding apparatus that affect even longitudinal seeding, studies were conducted using the method of multifunctional planning of experiment. An experimental peg-wheel feed for a pneumatic nursery planter SSNP-16 has been manufactured. Main factors affecting the quality parameters of seeding process are the following: the number of toothed rollers k = 48; 72; 96; speed ratio changer that rotates the extreme roller disks, i = 1.17; 1.55; 1.93; rotation frequency of the central part of toothed roller n = 12; 16; 20. The best criteria is uneven longitudinal seeding v , %. The optimal values of key factors were found: the number of toothed rollers k = 87, speed ratio changer that rotates the extreme disks, i = 1.77, rotation frequency of the central part of toothed roller n = 16 rpm. With these values of factors, uneven longitudinal seeding does not exceed 22.5%.seederapparatuscoilseedingunevennessoptimizationsteam meterсеялкааппараткатушкавысевнеравномерностьоптимизацияпараметр[Доспехов, В. А. Методика полевого опыта (с обоснованием статистической обработки результатов исследований) / В. А. Доспехов. - М. : Колос, 1979. - 416 с.][Исаев, Ю. М. Высев семян спирально-винтовым аппаратом / Ю. М. Исаев, Н. М. Семашкин, В. А. Злобин // Международный журнал экспериментального образования. - 2014. - № 8-3. - С. 75-76.][Ларюшин, Н. П. Обоснование выбора конструкции высевающего аппарата зерновой сеялки / Н. П. Ларюшин, А. В. Шуков, В. А. Мачнев // Нива Поволжья. - 2012. - № 2 (23). - С. 59-65.][Ларюшин, Н. П. Результаты лабораторных исследований высевающего аппарата / Н. П. Ларюшин, В. Н. Кувайцев, С. Д. Загудаев [и др.] // Фундаментальные исследования. -2013. - № 10-1. - С. 140-144.][Пат. №2473200 РФ, МПК A01C 7/12. Высевающий аппарат / Петров А. М., Сыркин В. А., Васильев С. А. [и др.]. - № 2011122286/13 ; заявл. 01.06.2011 ; опубл. 27.01.13, Бюл. №3. - 7 с.][Петров, А. М. Результаты полевых исследований экспериментальной селекционной сеялки с катушечно-штифтовым высевающим аппаратом / А. М. Петров, В. А. Сыркин // Известия Самарской государственной сельскохозяйственной академии. - 2017. - № 2. - С. 36-39.][Сыркин, В. А. Обоснование конструкционно-технологической схемы катушечно-штифтового высевающего аппарата / В. А. Сыркин, А. М. Петров, С. А. Васильев // Известия Самарской государственной сельскохозяйственной академии. - 2011. - № 3. - С. 44-46.][Сыркин, В. А. Результаты экспериментальных исследований катушечно-штифтового высевающего аппарата / В. А. Сыркин, А. М. Петров // Достижения науки агропромышленному комплексу : сб. науч. тр. - Кинель : РИЦ СГСХА. - 2013. - С. 85-88.][Isaev, Yu. M. Theoretical studies of movement of loose material in a dosing device / Yu. M. Isaev, N. P. Kryuchin, N. M. Semashkin, A. N. Kryuchin // International Journal of Mechanical Engineering and Technology. - 2018. - Т. 9, № 5. - С. 834-840.][Kotov, D. N. Determination of speed of movenment of the particle on the rotating cone with shovels / D. N. Kotov, Yu. M. Isaev, N. P. Kryuchin [et al.] // International Journal of Mechanical Engineering and Technology. - 2019. - Т. 10, № 2. - С. 1507-1514.]