Bulletin Samara State Agricultural AcademyBulletin Samara State Agricultural Academy1997-32252782-4225Samara State Agrarian University22928Research ArticleFEATURES OF ELASTIC WAVE INFLUENCE FOR MASS TRANSFER PROCESS IN METALS AND ALLOYSMironovaT Fcand. of physical and mathematical sciences, associate prof. of the department «Physicist, mathematics and information technologies»tmironova51@mail.ruMironovaT Vcand. of physical and mathematical sciences, associate prof. of the department «Physicist, mathematics and information technologies»mirt_777@mail.ruFSBEI HVE Samara SAA150920153899211032020Copyright © 2015, Mironova T.F., Mironova T.V.2015The purpose of research - to improve the mechanical properties and surface quality of metal products on the basis of copper, titanium, iron and its alloys. Cylindrical samples with 10 mm diameter and 10 mm height made from pure metal have been exposed the repeated treatment at a pressure of elastic waves to 107 Pa at a frequency of up to 60 pulses per minute in a neutral gas and permeating gas medium. The treatment temperature was varied in the range of 973-1273 K. Method of autoradiography and stratified radiometric analysis with help of device «Beta 1» and using isotopes 63Ni, 14C were applied. It was found that the rate of diffusion of nickel into iron, copper and titanium increased to 2 times and besides the concentration profile in titanium is nonmonotonic and the diffusion zone depth exceeded those in copper and iron. The observed acceleration of the process saturation with carbon increase 1.5-2 times at a temperature of 1273 K in 10 times at a temperature of 973 K during carburization iron and its alloys and titanium chromium as a result of treatment. At the same time the phase formation character change and after the pulse treatment of iron surface layer with 40 microns depth contained up to 65% of the austenite. Found that under the pulse compression of the gaseous medium occurs a maximum concentration of carbon, and, respectively, the microhardness maximum occurs, whose position is determined by the processing parameters and the composition of the alloy. Lowering the temperature diffusion annealing increased the efficacy of pulse treatment.mass transfer processmetalsradioactiveisotopeselasticwaveмассопереносметаллырадиоактивныеизотопыупругиеволны[Мазанко, В. Ф. Диффузионные процессы в металлах под действием магнитных полей и импульсных деформаций : монография: в 2 т. Т. 2 / В. Ф. Мазанко, А. В. Покоев, В. М. Миронов [и др.]. - М. : Машиностроение, 2006. - 320 с.][Бокштейн, Б. С. Диффузия атомов и ионов в твердых телах : монография / Б. С. Бокштейн, Я. Б. Ярославцев. - М. : МИСИС, 2005. - 362 с.][Азаренков, Н. А. Моделирование диффузионных процессов и экспериментальное определение параметров диффузии в конструкционных материалах с использованием радиоактивных изотопов / Н. А. Азаренков, В. Е. Семененко, Н. Г. Стервоедов [и др.] // Вопросы атомной науки и техники. - 2007. - №2. - С. 76-81. - (Серия «Физика радиационных повреждений и радиационное материаловедение»).][Бородавка, А. Е. Компьютеризированный комплекс для исследования процессов диффузии в металлах и сплавах радиоактивным методом / А. Е. Бородавка, А. С. Посухов, В. Е. Семененко [и др.] // Радиофизика и электроника. - 2005. - №4. - С. 162-165.][Бобырь, С. В. Анализ процесса графитизации в железоуглеродистых сплавах на основе термодинамики необратимых процессов // Металлофизика и новейшие технологии. - 2013. - Т. 35, Вып. 2. - С. 199-208.][Котречко, С. А. Новые подходы к оценке взаимосвязи свойств прочности, пластичности и механической стабильности / С. А. Котречко, Ю. Я. Мешков, А. В. Шиян [и др.] // Металлофизика и новейшие технологии. - 2011. - Т. 33, вып. 9. - С. 1277-1290.][Azhaza, V. M. Microstructure and hardness of natural composite materials / V. M. Azhaza, N. A. Azarenkov, V. E. Semenenko, V. V. Podzolkova // Modern Materials Science: Achivements and Problems. - Kiev, 2005. - Vol. 1. - P. 15-17.]